Famco Chimney Cap & Crown Nationwide

Famco Chimney Cap & Crown in Severna Park: What to Know First

We provide independent Famco chimney cap and crown service in Severna Park, with most jobs completed in a single visit and upfront pricing agreed before we start. A standard Famco cap replacement runs $340-$620; crown repair or coating typically falls between $450-$890 depending on accessibility and damage. We are not affiliated with or authorized by Famco - we are an independent service provider who stocks and installs Famco parts alongside professional-grade alternatives from DuraFlex, HeatShield, and Gelco.

Call (443) 464-2560

This page is for Severna Park homeowners who already have a Famco cap or crown and need honest answers about what is wrong, what it will cost, and whether it can wait. If you are on the fence, call (443) 464-2560 and a live person will pick up, 24 hours a day.

How Famco Products Fail - and How We Fix Them

• Famco 13×13 and 8×12 galvanized single-flue caps - The spot-welded seam where the lid meets the skirt cracks after 7-10 years in Severna Park’s salt-air environment, especially on homes within a mile of the Magothy River. Water wicks through the seam, rusts the interior mesh, and stains the flue tile below. We pull the cap, inspect the flue for spalling, and install either an OEM Famco replacement or a Gelco stainless equivalent with a fully welded lid - no spot welds, no repeat failure.
• Famco multi-flue caps (Model 75 and 100 series) - The 24-gauge galvanized base pan pools condensation on north-facing chimneys during Severna Park’s March and November freeze-thaw cycles. The pan bows, pulls away from the mortar bed, and creates a gap where squirrels nest. We remove the pan, re-pitch the crown surface toward the flue, and reset with a stainless base pan and new masonry anchors - or recommend a full crown rebuild if the substrate is too far gone.
• Famco wind-directional caps (WD series) - The aluminum wind vane seizes after 3-5 years of pollen and salt buildup, locking the cap in one position and defeating its purpose. On a job last spring off Benfield Road, the vane was frozen facing east, so every west wind drove rain straight down the flue. We disassemble the vane, clean the pivot, lubricate with high-temp graphite, and replace the bushing - or swap to a stationary Famco cap if the homeowner does not want the maintenance.
• Famco crown wash coatings - Famco’s brush-on crown sealant is often applied too thin by original installers, especially around the flue collar where the crown meets the terracotta. In Severna Park’s sun, the thin spots alligator and crack within 18 months. We grind back to sound concrete, apply a sloped CrownCoat or HeatShield rebuild mix at proper thickness (minimum 3/8 inch at the flue, tapering to the edge), and finish with a breathable silane-siloxane sealer.
• Famco chimney cap mesh (all series) - The 5/8-inch spark arrestor mesh on older Famco caps clogs with creosote in wood-burning setups along the B&A Trail corridor, where homeowners burn oak and hickory six months a year. The restricted draft causes smoke backup and accelerates creosote buildup inside. We clean or replace the mesh with 3/4-inch stainless, which flows better while still meeting code, and we document the flue condition with camera photos the homeowner can see.

Our Famco Chimney Cap & Crown Process

1. 1
   Call and schedule. A live person answers, 24/7. We ask the cap or crown model if you know it, the symptoms, and whether you have photos. We book a 2-hour arrival window.
2. 2
   Level-2 camera inspection on arrival. Our tech photographs the cap or crown from the roof, then runs a camera down the flue to check for water damage, spalling, or liner gaps caused by the failure. You see the photos on the spot.
3. 3
   Parts decision. If the Famco part is available and cost-competitive, we quote OEM. If lead time is 3+ weeks or the design has a known weakness, we quote a quality aftermarket equivalent - Gelco for caps, HeatShield for crown rebuilds - and explain the trade-off. No surprises on the bill.
4. 4
   The repair. For caps, we remove the old unit, inspect the flue tile and crown surface, install new with proper fasteners and high-temp sealant. For crowns, we grind, form, pour or coat, and slope to drain. Most jobs finish in 2-4 hours.
5. 5
   Test and document. We run a draft test, verify no leaks with a water check on the crown, and email you the photo report with the plain-English verdict.
6. 6
   The guarantee. Every job carries our 90-Day Done Right Promise in writing. If it is not right, we come back. No paperwork, no arguing.

What Famco Chimney Cap & Crown Costs in Severna Park

These are Severna Park numbers for 2024-2025, based on our actual invoices. We do not quote over the phone without seeing the chimney - every estimate is free, in person, with photos you can see. Call (443) 464-2560 to schedule.

Why Severna Park Homeowners Call Hearthstone Chimney Co. for Famco Work

We have worked chimneys in Severna Park for over 42 years, including the older wood-burning fireplaces along the B&A Trail corridor that see heavy use every winter. Russell Haines and our crew know which Famco caps hold up in salt air and which do not, and we stock the alternatives - DuraFlex, HeatShield, Gelco - when OEM is not the right call.

Our 90-Day Done Right Promise is in writing, no arguing. Calls are answered by a live person 24/7, not a callback queue. Our techs are background-checked, uniformed, and trained to document every inspection with photos and a plain-English verdict. If the chimney is not safe to use, we will say so. If it is, we will say that too.

FAQs